Re: Fails at 1% with error "FAILED: An error occurred during the conversion:...
I had the same issue when converting a Version 1 VM to a VCenter V5 VM, but it was caused by disk inconsistencies in the running VM. I shut down the Version 1 VM and told the converter to use the VM...
View ArticleRe: Unable to enter license key on OpenSuse 12.2 64 bit - SOLVED
how can it be done on Ubuntu ? - no su , only sudo .. and sudo sh ./Vmware.... does not help.
View ArticleRe: Can't load kernel modules into Linux kernel
/includ/ is a typo, it should say /include/
View Articleshow process id for UDP socket in esxi 4.1
How do you find out which process is using a UDP port in ESXI 4.1 ? 3 of my ESXi 4.1.0 (260247) servers are sending UDP traffic to 50.17.133.11 (ec2-50-17-133-11.compute-1.amazonaws.com), destination...
View ArticleRe: Another licensing question
ESXi 5.0 hosts only supports up to 32 vCPUs in the Enterprise Plus edition. So you either have to upgrade the license or upgrade to vSphere 5.1. André
View ArticleQuestion - XP Microsoft Application Crash Report- How to grab?
I just installed 'Miasmata' purchased from GOG.com in an XP vm guest under a Windows 8 host. It apparently installed and configured without a hitch but immediately crashed on launching. It is a...
View ArticleRe: New !! Open unofficial storage performance thread
Hey guys, I know this thread isn't the most active place on the internets but I'm hoping maybe a storage networking guru can help me out. I'm troubleshooting poor performance on our iSCSI SAN and...
View ArticleESXi realtime performance chart don`t show in vCenter 5.1a
Hi expert My vcenter server don't show esxi performance data.I found KB:2009291 Cannot view the realtime Performance Overview charts after upgrading to vCenter Server 5.0 (2009291) But My vcenter...
View ArticleRe: New !! Open unofficial storage performance thread
Sono fuori ufficio.Per urgenze contattare l'assistenza tecnica allo 045 8738738 o inviare una mail a supporto.tecnico@rtc-spa.it Francesco BonettiRTC SpA
View ArticleWhere is upgrade ISO for vSphere Data Protection 5.1.11?
This URL says that a new version was released:vSphere Data Protection 5.1.11 Release Notes I went to downloads and the only upgrade I see says this: VMwareVDPUpgradeFrom61To-6.1.82-57.iso File size:...
View ArticleRe: cannot connect to profile-driven storage service
If you are the Original Poster, you have the option to award points to a specific post. Basically, it's two buttons that say "Helpful" and "Correct" This is why we suggest having separate threads for...
View ArticleRe: New !! Open unofficial storage performance thread
If removing one of the switches from the configuration is resulting in that significant of a performance increase, then I suspect there may be something up with the stacking. How are the switches...
View ArticleVM presence on multiple vlan question
I am trying to have a VM with a presence on multiple vlans. This is a temporary situation that will be resolved once the needed switch actually arrives. Unfortunately that will be several weeks. I...
View ArticleClik here to view.
Beginner setup
Hi I am fairly new to configuring ESX from the bottom - I have worked with preconfigured ESX-hosts for a couple of years. I have a few questions about configuring the network-cards.I think its best if...
View ArticleRe: Virtual Network Editor not saving added networks
Cheers André, I was actually running 9.01 so did an upgrade this afternoon...same problem sadly....I'll have a look at the release notes see if same issue... Thank you
View ArticleRe: VM presence on multiple vlan question
With the physical uplink ports configured as a trunk/tagged (802.1Q) port you can create multiple port groups on the vSwitch, each with another of the required VLAN IDs and connect the VM to those port...
View ArticleRe: Beginner setup
Welcome to the Community - YOu can create a virtual switch with no uplink ports - your VMs will connect to this as well as the PfSense router whcih will also connect to the existing VM port group -
View Article